Thank you for purchasing our product.
This wireless driveway and intruder alert has a 500 ft(150m)
range. It is great for multiple applications,including:
Alerting you when visitors enter your driveway
Deterring trespassers and thieves from entering your property
or building.
Alerting you to wildlife on your land.
Using in drive-thrus to signal that a customer has pulled in,and
more.
Our receiver is expandable,which allows you to pair various
transmitters
such as contact sensor,motion detector,doorbell button etc.
One doorbell receiver can pair with up to 50 various transmitters and
each transmitter can be set to different ringtones.
Welcome
1 2 3
4
Passive Infrared (PIR) Sensor & Receiver
Wireless RF Transmission Up to 500 feet
Sensor Detects Motion and Triggers the Receiver to Turn on a
Chime
Sensor Detection Range up to 13
Feet (mounted at 50' height)
Sensor Detection Angle up to 30 Degree
4 Levels of Sound Volume Sensor – 4*AA Battery Operation
(battery not included)
Receiver-AC100~240V Operation
Battery Low Indicator LED for Sensor
Trigger LED on Sensor
Wireless, Easy Installation
Features
Overview
Push button
Wall bracket
5 6 7 8
Please read this user manual before using and installation
Select melody
5S
Hold volume button for 5s
AC Plug
Volume control
Backward button
Forward button
Speaker
PIR motion sensor
You can pair up to 50 sensors to your receiver and each sensor can
have its own unique melody.
Indoor Chime Receiver
The receiver has up to 52 melodies for you to choose from. You
can also have multiple receivers in different locations in your home
or business, so you can hear the alarm chimes.
LED indicator
Basically, there are two parts to the Driveway Alert system.
1.The Indoor Alarm Receiver works as an alarm buzzer and a door
chime (the melody play once only). It monitors for signals coming from
the Passive Infrared (PIR) Motion Sensor and activates an alert in
response to that signal. It also features a LED indicator so you can
visually tell when an alert is coming. The Indoor Alarm Receiver can be
simply plugged to an AC outlet.
Water Resistant Sensor
How Does It Work?
Getting Started
1.POWERING THE INDOOR CHIME RECEIVER
Plug the receiver into the outlet. The receiver will perform better if
kept away from other electrical equipment (eg TV,microwave.
2.POWERING THE PIR MOTION SENSOR
The motion sensor runs on four (4) AA batteries (not included)
and operates wirelessly at a maximum distance from the receiver
of 500 ft (150 m).
To insert batteries into the motion sensor,
(1)Remove the screws from the four corners of the back of the
motion sensor to access the battery compartment.
(2)Install 4*AA batteries,replace the cover a
nd secure the screws.
3.SOUND VOLUME CONTROL:
Press the volume control button on the receiver to cycle through 4
volume levels.
4.SETTING RINGTONE FOR A TRANSMITTER:
There are 52 melodies to choose from
(1)Press the Forward Button or Back Button to choose your
favorite ringtone.
(2)Please follow the pairing steps below to sync the new
ringtone.The new ringtone will be set for the most recently synced
transmitter.
5.PAIRING A TRANSMITTER TO THE RECEIVER
6.TWO OR MORE TRANSMITTERS PAIRING
The pairing mode is required for each transmitter.For two or more
tran
smitters,please follow the pairing steps(1)-(3) for each
transmitter.
7.RESET
Press Forward Button for 5 seconds to reset receivers to default.
When receiver sounds ‘Ding Dong’ with LED flashing that means
the reset was successful.After a reset receivers revert back to
the 1st ringtone and transmitters must be paired again.
Please note:
(1).Pairing mode will last for 5 seconds only before timing
out.Ensure you activate the transmitter during this time or the
process will have to started again.
(2)Pairing mode will quit automatically after paring is
completed.
We recommend mounting the motion sensor at least 3 to 4 ft (1 m)
above the ground on a sturdy, no-metal surface (i.e. a wall, wooden
post or tree) with the sensor eye pointed straight out over the area you
wish to cover (such as up your driveway looking towards your house).
This will decrease or eliminate false alarms from small animals, give
you a longer area to pick up movement, and avoid unwanted alarms
from nearby lawns/roads
2.The PIR Motion Sensor enable you to detect movement of people and
vehicles, while allowing small animals to pass through undetected. it will
send a signal to the Indoor Alarm Receiver whenever motion is
detected. The motion sensors should be deployed outdoors, where
there is a clear view of the driveway or the likely entry and exit paths
that you plan to secure.
Sensor Eye
Sunshade & Back cover
(1)Please select your favourite
ringtone before pairing.
(2)Press the volume control
button for 5 seconds until a Ding-
dong is heard and the LED
indicator starts flashing-you are
now in pairing mode.
(3)Active the PIR Motion sensor to send a signal to the receiver
WAVE your hand in front of
the motion sensor to
activate
Installing the PIR motion sensor
Note:
Always test that your sensor is working in your desired location
before installing it. Avoid placing your sensor in a location where
sunlight will shine directly into the sensor eye. Direct sunlight may
cause false alarms or damage to the PIR sensor.
Tools you will need for installation:
-Pencil
-Phillips screwdriver
-Electric drill with 3/32” and 7/32” drill bits (recommended)
-Hammer (optional)
(1). Mark the mounting holes with a pencil.
(2). If installing on a wooden surface, you only need to use the
included screws. Drill out your pilot holes using a 3/3
2” drill bit to a
depth of ¾”. This will help prevent stripping of the screws and hold
the sensor more securely.
(3). If installing on any other surface, such as brick or masonry,
you will use the included screws and anchors. Drill out your pilot
holes using a 7/32” drill bit to a depth of 1”. Gently tap the anchors
into your pilot holes using a hammer until the anchors are flush
with the mounting surface.
(4). Screw the bracket base to the place you want to install.
(5). Screw the sunshade onto the shaft of the bracket.
(6). Replace the sunshade and secure the screws
(7). Twist the ball onto the fixed base of t
he bracket just until tight.
Do not over-tighten.
(8). Adjust the angle of your sensor so that it is looking at your
target area.
9 1
0 11
Sunshade & Back cover
Ball & Shaft
Bracket base
Wireless Driveway
And Intruder Alert
User Manual
